HPAVC/HPAVC CD-ROM.iso/pc/XMODEM.ZIP/xmodmcrc.txt

Text File | 1996-03-06 | 5.2 KB | 140 lines

Perception presents:
---------- Understanding The X-Modem CRC File Transfer Protocol --------------

                  by Em Decay

This has to be one of the most internationally accepted protocols for upload-
 ing and downloading binary and text files.  It is fairly straight-forward as
 to how it is set up and there are some error checking capablities.


--- Before you begin ---

Look at my XMODEM.TXT text file for a general understanding of the X-Modem
 file transfer protocol and the terms used in it.

New things you need to know beforehand...

One word is the same as two bytes.  If you want the high byte and the low
 byte of a word, simply do the following.
   High byte = word DIV 256   (DIV is the same as divide except the answer is
                  truncated)
   Low byte = $00ff AND word  (AND refers to AND logic)

To get a word from a high byte and a low byte, simply multiply the high byte
 by 256 (or shift it left 8 bits, if you know assembly) and add the low byte
 to it.

CRC stands for Cyclical Redundancy Check.  In X-Modem CRC, it is also refer-
 red to as CRC-16 since there are 16 bits (1 word) at the end of the block
 that contain the CRC.  This 1 word CRC replaces the 1 byte checksum in
 X-Modem.
CRC-16 guarantees detection of all single and double bit errors, all errors
 with an odd number of bits and over 99.9969% of all burst errors (you don't
 have to know what all these things are :).
The easiest and fastest way to calculate the CRC is to use a lookup table.

Here is some source code about making a lookup table.  Call this procedure
 at the very beginning of the program.  Make crctable an global variable.
 It is an array [0..255] of word.

 procedure initcrc;

   var
     i:integer;

   function calctable(data,genpoly,accum:word):word;

     var
       j:word;

     begin
       data:=data shl 8;
       for j:=8 downto 1 do
     begin
       if ((data xor accum) and $8000)<>0 then
         accum:=(accum shl 1) xor genpoly
       else
         accum:=accum shl 1;
       data:=data shl1;
     end;
       calctable:=accum;
     end;

   begin
     for i:=0 to 255 do
       crctable[i]:=calctable(i,4129,0);
   end;

The CRC starts with a value of zero at the beginning of each block.  Now to
 update the CRC, with each byte in the 128 byte packet simply do this (the
 oldcrc is the crc value to be updated, data is the current byte):
     CRC:=(oldcrc shl 8) xor (crctable[(oldcrc shr 8) xor data]);
The final value of the CRC (after all 128 bytes) is what is being sent in the
 X-Modem CRC protocol.

If you have somewhat understood what has just been described then you catch
 on a lot faster than I did :)  If you just use


--- The Actual Transfer ---

As in X-Modem, the uploader waits for the downloader to send the NCGbyte.
 The NCGbyte for X-Modem CRC is chr(67) or the capital letter C (unlike
 X-Modem where the NCGbyte is chr(21), the NAK).  If the downloader takes too
 long or an error occurs then the uploader will stop waiting or "Time Out".
 If this happens, then the file transfer must restart.

With each packet sent...

    The uploader sends:

    1. an SOH byte                             {1 byte}
    2. the packet number                       {1 byte}
    3. the 1's complement of the packet number {1 byte}
    4. the packet                            {128 bytes}
    5. the high byte of the CRC-16             {1 byte}
    6. the low byte of the CRC-16              {1 byte}

    These six things make up the block.

    The downloader:

    1. ensures that the packet number sent matches the actual packet number
     that it is (If the third block sent has a '4' as the second byte,
     something is wrong --> CANCEL TRANSFER (send CAN byte))
    2. adds the packet number and the 1's complement of the packet number
     together to make sure that they add up to 255.  if they don't -->
     CANCEL TRANSFER
    3. sets the CRC to zero
    4. updates the CRC as each byte in the packet is sent
    5. compares the calculated CRC to the CRC that is sent
    6. if everything looks ok (calculated CRC=sent CRC), then the downloader
     appends the bytes in the packet to the file being created (sent).
     The downloader then sends an ACK byte which tells the uploader to
     send the next block.
       if the CRCs do not match, then the downloader sends a NAK byte which
     tells the uploader to send the same block it just sent over again.

When the uploader sends an EOT byte instead of an SOH byte, the downloader
 sends a NAK byte.  If the uploader sends another EOT immediately after that,
 the downloader sends an ACK byte and the transfer is complete.

Another thing, the downloader can cancel the transfer at any time by sending
 a CAN byte.  The uploadered can cancel only between blocks by sending a CAN
 byte.  It is recommended that you send between 2 and 8 consecutive CAN bytes
 as some communication programs will not allow you to cancel with only 1 CAN
 byte.


--- Wrap Up ---

Hopefully, you were able to follow along. :)  If not, you can e-mail me at
 [e-mail]  and I will try to clarify it for you.  Have fun :)

Perception:    Em Decay -- Mark Korhonen
           Cmf ------- Chris Fillion

Written on Jan.3/95